# 8 Cross-sectional Properties

Anahita Khodadadi

Designing Structural elements requires the knowledge of applied external loads and internal reactions, material strengths, and cross-sectional properties. The geometrical properties of a structural element are critical in keeping axial, shear, and bending stresses within allowable limits and moderating the amount of deflection. The following demonstrations show how the shape of the cross-sections affects their stiffness.

*Figure 8-1: Relation between the cross-sectional depth (rise) of a beam and its stiffness*

Chapter 7 discussed that “area” is one of the cross-sectional properties, which is important to reduce the amount of stress in beams and columns. This chapter focuses on the shape of the cross-sectional area and its distribution about the neutral axis of beams. In the following, some cross-sectional properties that will be necessary to calculate beams and columns are introduced.

## Center of gravity

The center of gravity of a body is the point about which the mass of the body is balanced or the point through which the weight of the body acts. When the density of a body is uniform throughout, the center of gravity and the centroid (geometric center) of the body are at the same point.

- The centroid of a rectangle is defined as the center point where all the diagonals intersect each other.
- A centroid of a triangle is the point where the three medians of the triangle meet.

*Figure 8-2: The center of gravity of some basic geometrical shapes*

*Video 8-1: Neutral axis in a beam (https://www.youtube.com/watch?v=BthnS6LJt8s&t=1s)*

You can use the following equation to find the center of Gravity of a compounded shape:

[latex]\bar{X}= \frac{\sum ({Area \times d_x})}{\sum{Area}}[/latex]

[latex]\bar{Y} = \frac{\sum( {Area \times d_y})}{\sum{Area}}[/latex]

### Example

## 1st Moment of Area

*Video 8-2: A demonstration of the moment of areas of two rods (https://www.youtube.com/watch?v=m9weJfoW5J0)*

By definition, the tendency of an area alone to rotate about an axis in the plane of that area.

Q = A[latex]\bar{x}[/latex]

At the Neutral/Centroid axis:

A_{1} x_{1} = A_{2}x_{2}

*Figure 8-3: The difference of 1st moment of area in two beams with different cross sections *

## 2nd Moment of Area/Inertia

By definition, the 2nd moment of area is the distance of force distribution from the neutral axis. The 2nd moment of area involved the first moment of area multiply by a second moment arm. The second moment arm is the distance between the centroid of the force distribution and the neutral axis.

*Figure 8-4: The pattern of force distribution in relation to the distance from the neutral axis*

The second moment of area of a beam with a rectangular section can be calculated using the following equation:

I_{x} = [latex]\frac{bh^3}{12}[/latex]

Where:

I_{x} = Second moment of area

h = depth of the beam

b = with of the beam

## Section Modulus

By definition, the section modulus (S_{x}) of a beam with a symmetric section equals its second moment of area divided by half its depth at the extreme fiber.

S_{x} = [latex]\frac{I_x}{c}[/latex]

Where:

S_{x} = Section modulus

I_{x} = Second moment of area

c= h/2 at extreme fibers of a symmetric section

h = depth of the beam

The section modulus will help determine the cross-section shape of a beam as discussed in the Chapter 9.

## Geometrical properties of steel beam cross-sections

Tables of design dimensions, detailing dimensions, axial flexure, strong-axis flexure, and weak-axis flexure of steel beams are provided in the Steel Construction Manual published by the American Institute of Steel Construction (AISC). You may find the cross-sectional area (A), depth of the beam (d), I_{x}, and S_{x}.

*Figure 8-5: Example of steel profiles listed in Steel Construction Manual [15]*